Q modeling
==============


Characteristics of modeling
-----------------------------------

This modeling is used to verify the construction of a reduced base on a field of type SIEF_ELGA.


Characteristics of the mesh
----------------------------

The mesh contains 27 elements of type HEXA8.


Tested sizes and results
------------------------------

Stress values are tested in non-regression at a few points of the complete problem. On
Always test an element in RID and an element outside of it (which will be useful next for
R modeling).


.. csv-table::

    "**Identification**", "**Reference type**"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIXX —Point 1"," NON_REGRESSION"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIYY —Point 1"," NON_REGRESSION"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIZZ —Point 1"," NON_REGRESSION"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIXX —Point 1"," NON_REGRESSION"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIYY —Point 1"," NON_REGRESSION"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIZZ —Point 1"," NON_REGRESSION"


These values are used as a reference to check the base produced on SIEF_ELGA that is being rebuilt
by modal combination (command CREA_CHAMP/ASSE).

From a base built with OPERATION =' POD 'and TOLE_SVD = :math:`{1,0}\times {10}^{-3}`
in DEFI_BASE_REDUITE:


.. csv-table::

    "**Identification**", "**Reference Type**", "**Tolerance**"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIXX —Point 1"," AUTRE_ASTER "," :math:`{8,0}\times {10}^{-3}`"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIYY —Point 1"," AUTRE_ASTER "," :math:`{8,0}\times {10}^{-3}`"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIZZ —Point 1"," AUTRE_ASTER "," :math:`{1,3}\times {10}^{-3}`"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIXX —Point 1"," AUTRE_ASTER "," :math:`{2,8}\times {10}^{-4}`"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIYY —Point 1"," AUTRE_ASTER "," :math:`{3,3}\times {10}^{-4}`"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIZZ —Point 1"," AUTRE_ASTER "," :math:`{3,8}\times {10}^{-4}`"


From a base built with OPERATION =' POD_INCR 'and TOLE_SVD = :math:`{1,0}\times {10}^{-3}`
and TOLE_INCR = :math:`{1,0}\times {10}^{-3}` in DEFI_BASE_REDUITE:


.. csv-table::

    "**Identification**", "**Reference Type**", "**Tolerance**"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIXX —Point 1"," AUTRE_ASTER "," :math:`{2,8}\times {10}^{-4}`"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIYY —Point 1"," AUTRE_ASTER "," :math:`{2,8}\times {10}^{-4}`"
    "Knit :math:`{CellInRID}` - SIEF_ELGA/SIZZ —Point 1"," AUTRE_ASTER "," :math:`{1,1}\times {10}^{-4}`"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIXX —Point 1"," AUTRE_ASTER "," :math:`{3,4}\times {10}^{-4}`"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIYY —Point 1"," AUTRE_ASTER "," :math:`{3,8}\times {10}^{-4}`"
    "Knit :math:`{CellOutRID}` - SIEF_ELGA/SIZZ —Point 1"," AUTRE_ASTER "," :math:`{5,0}\times {10}^{-4}`"